Did you just try to flush your toilet, and nothing happened? Look inside the tank, and you may see no water inside. Before you stress, rest easy that fixing this problem is usually easy to accomplish. If you can’t complete this yourself, you can always schedule toilet repair with a knowledgeable plumber. Follow these guidelines to diagnose and repair the problem of no water in the toilet tank.
Check the Water Supply
The first action is to verify that the water is running. If you or someone in your household recently performed a toilet repair, you most likely turned off the water first. Did you neglect to turn it back on? To check, rotate the water shut-off valve on the wall behind the toilet. If the valve was shut, water will now start refilling the tank. If this doesn’t work, test the water at your sink or another plumbing fixture. If nothing flows from the tap, you might have a more substantial water supply issue. Call your water company to learn more.
Reposition or Replace the Float Mechanism
Older toilet designs use a float ball to determine the water level as it rises in the tank. When the ball passes a specified height, the float arm it’s joined to stops the water flow. However, insufficient water might enter the tank if the ball is positioned improperly or the arm is broken. To adjust the float ball, start by removing the toilet tank lid. Bend the float arm up a little to adjust where it sits in the tank. If this fails to fix the problem, you might need to replace the full float mechanism. You should be able to perform this yourself by following the detailed steps that come with the replacement parts, or you can employ a plumber for help. Just realize that float balls are old toilet systems. You may prefer improved durability and efficiency if you upgrade the existing tank components or replace the toilet completely.
Adjust the Fill Valve
Modern toilets utilize a float cup rather than a float ball, coupled with a fill valve and water level rod. There may very well be no water in the toilet tank because the valve has slipped out of place or become blocked. Here are some techniques to try:
- Test the fill valve: Have a look inside the toilet and find the fill valve on top of a vertical tube device on the left side of the tank. Make sure it’s secure and evenly connected to the tube. Then, adjust the water level. Current models of toilets have an adjustment knob you can turn by hand, while older versions may require you to loosen an adjustment screw with a flathead screwdriver. Flush the toilet and make it possible for the tank refill to test the water level. Change it until the water comes to about one inch below the top of the overflow tube.
- Clean the fill valve: Mineral buildup and other crud may be blocking the valve and keeping your toilet from filling. Shut off the water behind the toilet and take off the fill cap. Then, gradually turn the water back on, cupping your hand over the valve to stop water from spraying all over. After several seconds, turn the water back off. Finally, wash the fill cap to clear away hard water buildup. If the cap is damaged, swap it out.
- Clean the valve tube: The tube below the fill valve may also be blocked. Shut off the water and take away the valve hardware. Then, insert a slim bottle brush or wire down the tube. Turn the water back on a little to flush away the junk. Replace the valve hardware and flush the toilet to check your adjustments.
Repair or Replace the Trip Assembly
If you’ve followed the steps above without positive results, the one remaining possibility is a damaged trip assembly. This part links the flush handle to the tank. If it’s not working or positioned inadequately, the flush cycle may not complete, leaving the tank empty. Remove the toilet tank lid and check the trip assembly attached to the handle. If it’s out of place, reposition it. If the assembly is bent, worn or busted, replace it. Whether you perform the job yourself or leave it to a plumber, this uncomplicated repair should get your toilet tank filled with water again.
Schedule Toilet Repair Today
You can’t go long without a working toilet, so reach out to [Company name] to schedule a toilet repair. We can determine why your toilet isn’t filling and suggest the appropriate fix. If your plumbing fixture is outdated and worn out, our team can install a high-efficiency toilet in your bathroom. Rest assured that every plumbing repair and replacement we complete is backed by a 100% satisfaction guarantee. To schedule a visit from one of our licensed professionals, please call your local [Company name] office today.